Hi all.

Had a sudden suspension fault come up and decided to get the IIDtool. Seems a great piece of kit and connects well with lots of useful functions.

Got fault in rear right(drivers side) height sensor with no voltage showing. Got new LR sensor from the dealership and replaced it. Cleared all codes and no faults come back.

Performing a calibration using Guided method is easy and without complication. However, after selecting the APPLY settings to he screen show s a procedure failed E1 notice and nothing is updated.

Problem is that the car has now decided that it will throw up a red warning and drop the sus to access height.

Any ideas as to what is the issue. I am a bit concerned that the settings for the height calibration are close for the 3 original sensors but the new one is wildly different.

example with car level and measurements set to 461 front and 465 rear the settings are 203 and 205 at the front and 213 with new sensor at 245.

Any help much appreciated.

Cheers

John SVR On My Wish-List
MY 2010 RR Sport TDV8 Autobiography (current)
MY 2006 RR Sport TDV8 HSE

I have the same tool but not needed to do the cal yet. It sounds like it has updated the settings but the settings were to far out and maybe then given you a fail. So maybe not a fail to update but the update has led to a fail. Did you save the original file? Have you tried re calibrating with new calculations? Did you use the guide on the GAP website?

Page 87 and 102 here

https://www.gap-diagnostic.com/wordpress/w...lV3.00.pdf 2012 5.0 SC AB
Mods:
TPMS
Genuine LR DRLs
Remote Boot close from key fob
2016 Discovery 4 Mirrors AKA RRS2
2014 L405 Surround Camera retro fit (WIP)
2013 RRS Dual View Screen fit (Complete)
2016 LR4 RSE
2014 LR4 Homelink
2016 FFRR Electrochromatic Wing Mirror Glass

70 plate Focus ST (Current)
1942 VEP Ford GPW Jeep (Willys) (Current)
1943 Whites M16 Halftrack (Current)
16 plate Eurofighter Typhoon, 2 x Eurojet engines with 20,000lbs thrust each. 1380mph

Last edited by Brit Plumber on Sun Jun 17 2018 9:48am. Edited 1 time in total

I also meant to say I don’t think the figures displayed are in my, they are just a figure. The guide suggests 493mm is a figure of 126 so if your in the 200 region, you could be trying to set the height to an impossible height. Again I’m no expert but trying to give you some avenues to explore. 2012 5.0 SC AB
Mods:
TPMS
Genuine LR DRLs
Remote Boot close from key fob
2016 Discovery 4 Mirrors AKA RRS2
2014 L405 Surround Camera retro fit (WIP)
2013 RRS Dual View Screen fit (Complete)
2016 LR4 RSE
2014 LR4 Homelink
2016 FFRR Electrochromatic Wing Mirror Glass

70 plate Focus ST (Current)
1942 VEP Ford GPW Jeep (Willys) (Current)
1943 Whites M16 Halftrack (Current)
16 plate Eurofighter Typhoon, 2 x Eurojet engines with 20,000lbs thrust each. 1380mph

Thank you for your thoughts Brit plumber.

I spent most of Sunday trying to get my head around why the car does not respond to the settings. It seems to work but what the actual real-world height is and the IIDtool measurements do not match.

As an electronic engineer, I have some understanding of the calibration procedure. basically, the system needs to have a datum point to work from and so setting the vehicle on a flat surface and adjusting the height for each corner to be 461mm at front and 465mm at the rear and locking in this calibration all makes clear sense. At this point, the height is known to the ECU and settings can be made with accuracy.

However, I get error showing and a failed E1 or sometimes E87 fault as the values are loaded into the ECU. It does seem to take the settings as you suggest but then when driving the car a few 1000 yards it throws up a red fault in sus and drops to the bump stops. (seriously unpleasant ride back home on the bump stops) I've not experienced this before and I do not recommend it to anyone.

The point I am asking is this. Since this faulty sensor has been replaced with new genuine part from the dealer should the calibration not bee somewhere near the original 3 other sensors. it does not seem to offer the same readings anywhere close.

I have loaded some images which will show you the issue. With the factory saved calibration loaded the car is rear down and front up. but the measurements that the IIDtool are showing are wildly out of sink both visually from the images of the real-world view.

If I follow the calibration procedure then the rear right (new sensor) has to read 245 with all original sensors at about 200 or lower. then it will not update and gives the E1 error and throws a red fault drops to bump stops when driving 1000 yards or so.


I'm totally baffled now. is it possible I have the sensor hooked up wrong? Cant see how but if anyone has an image of the sensor correctly connected that would be a relief.

Does the sensor need to be coded to the car? I ask this because the part guy said it die but I dismissed this because I considered it an attempt to generate workshop work for a simple sensor replacement.

HELP Please!!










 SVR On My Wish-List
MY 2010 RR Sport TDV8 Autobiography (current)
MY 2006 RR Sport TDV8 HSE

So when you first plugged in your IDD tool it would have saved the original setting's you can reset every thing back to it was as long as there were no original faults as they would also be put back you can try this or you can email pat at gap as they would be able to help and yes i would have thought if you just tried to set the one new ride sensor first before trying to reset all four it may be the right way to do it but i may be wrong

Thanks.
I did save the settings and the images posted are those that were saved loaded again.

Could you assist me with the details of the Pat you mentioned so I can email them now? there does not appear to be any form of contact phone details on their website.

Cheers

John SVR On My Wish-List
MY 2010 RR Sport TDV8 Autobiography (current)
MY 2006 RR Sport TDV8 HSE

Just log in to your account and then use the contact form

Sorry go through support then contact

Have emailed Gap and they are now talking to me.
Will update this thread as soon as the issue is resolved. SVR On My Wish-List
MY 2010 RR Sport TDV8 Autobiography (current)
MY 2006 RR Sport TDV8 HSE

This has been an interesting thread and saved me a future question. Hopefully it will all be a sorted soon!! 2012 5.0 SC AB
Mods:
TPMS
Genuine LR DRLs
Remote Boot close from key fob
2016 Discovery 4 Mirrors AKA RRS2
2014 L405 Surround Camera retro fit (WIP)
2013 RRS Dual View Screen fit (Complete)
2016 LR4 RSE
2014 LR4 Homelink
2016 FFRR Electrochromatic Wing Mirror Glass

70 plate Focus ST (Current)
1942 VEP Ford GPW Jeep (Willys) (Current)
1943 Whites M16 Halftrack (Current)
16 plate Eurofighter Typhoon, 2 x Eurojet engines with 20,000lbs thrust each. 1380mph

I get "Operation Failed E40" and "E41".

I have never been successful calibrating the height.

Pat will get you sorted, he’s very good and gets back to you really quickly... last time I needed to update new version when I got an error. ____________________
Current: MY2019 3.0 SDV6 Autobiography in Carpathian Grey
Gone: MY2015 4.4 SDV8 Autobiography in Corris Grey with ebony and lunar leather
Gone: MY2013 3.0 SDV6 HSE Black Edition in Orkney Grey, piano trim, black leather with contrast stitch

maybe you need to configure the new height sensor in the CCF first RRS 3.0 SDV6 HSE Lux
RRS 3.0 TDV6 gone
LR 3 HSE V8 gone
DiscoveryII V8 Gone
Discovery 1 V8 Gone
Mustang Shelby
Alfa Guilia (classic)

You have a fault with the rear left sensor too, going by those readings...